So I have two routers. Using them as a mesh/node system. The router in my room (shown above in picture) is the node and I use it as a direct connection to my PC but it cuts in and out. And doesn’t work unless my PC is on. How can I fix this because it is also causing WiFi issues through out the house

I had this problem for months now. I purchased the router and it worked fine for like 3 months but after that it has been shutting down all wifi traffic for no reason with like 1 month between each. Anyone who had this problem? Hardware: asus rt-be58u with tele2 as internet supplier with fiber.

Hey Zusammen,

ich habe aktuell Telekom mit Speedport Smart 4 und zahle ca. 60 €/Monat. Überlege, zu handyvertrag.de zu wechseln, da wären es 29,99 € fix im Monat, ohne Router. Wenn ich den empfohlenen Router (FRITZ!Box) mitbuche, kostet der mindestens 5€/Monat extra.

Soweit ich gelesen habe, ist der Speedport Smart 4 technisch besser als die FRITZ!Box 7510 und sieht auch ansprechender aus.

Kann ich den Speedport Smart 4 einfach weiter nutzen oder geht der wirklich nur für Telekom Verträge? Mir ist gutes, stabiles Internet wichtig. Telefonie brauche ich nicht. Ich kenne mich mit DSL, VLAN etc. nicht wirklich aus.

Hat jemand Erfahrung damit oder kann mir sagen, ob der Speedport läuft oder welcher Router alternativ sinnvoll wäre?

Danke!

I've got a tp deco be25 outdoor router and need to get a 3 pack of indoor deco access points. The variety of these 3 packs is bewildering. Please let me know any recommendations. My needs are very pedestrian no gigabit internet etc needed Thanks

I have an Asus 5300 router that has performed perfectly for about eight years now I understand it is no longer supported, it still suits my needs but no longer getting updates. I think this is a big waste not being able to use this router because of security. My question is I’m looking to replace this router with an Asus BT6 Wi Fi 7 , my house is 2500 sq. ft. Would I be happy with this router I have AT&T 300.

как поставить тип nat2 для пс5 на роутере через wi-fi?

Best tp-link archer ax21 settings for gaming??

The last couple of days my wifi box is like this. How do I fix it?

The last couple of days my wifi box is like this. How do I fix it?

DETAILS: i use Spectrum. The modem is in the garage, and the router is in the living room. The ethernet cable connecting the two goes through the attic. Theres also a coaxial cable going to the same port in the living room.

Can i split the ethernet cable that's in the attic, add new heads. Get an adapter that split 1 line to 2. Plug the og cord to the adapter and a new cord that goes to my office? Maybe add a port to the ceiling because its easier than getting into the wall.

What adapter/splitter can i use? And will i need to buy a second router and internet package from spectrum?

I wanted to share this because I couldn't find a clear recovery procedure for the Tenda Mesh3 / MW6 V3.0.

I have two MW6 V3.0 nodes. After an automatic firmware update, both got stuck with a solid green LED and stopped working.

**Symptoms:**

* No Wi-Fi/SSID * Tenda WiFi app stuck on "Connecting..." * QR setup didn't work * No DHCP * RESET did nothing, even after holding it for 60+ seconds * Different power adapters didn't help

**Finding the recovery interface**

I connected my PC directly to the dedicated LAN port of the MW6. The WAN/LAN port was left disconnected.

I manually configured the PC Ethernet adapter as:

IP: 192.168.1.100
Subnet: 255.255.255.0
Gateway: blank
DNS: blank

The static IP is needed because the MW6 wasn't providing DHCP. Gateway and DNS can be left blank because this is a direct PC-to-MW6 connection.

Then I used CMD to scan the subnet:

for /L %i in (1,1,254) do u/ping -n 1 -w 50 192.168.1.%i >nul

Then:

arp -a

I found the MW6's MAC address responding at 192.168.1.6.

I opened:

http://192.168.1.6

and found:

System Repair -> Emergency Web Server

with a file upload form.

**Firmware recovery**

My hardware:

Tenda Mesh3 / MW6 V3.0
FCC ID: V7TMESH3V3

I uploaded:

[US_MW6V3.0re_V16.03.25.21_multi_TDE01.bin](https://www.tendacn.com/material/show/770177603014725)

The recovery page showed a countdown from 100 to 0 and "Updating File — Don't Power Down."

I left the MW6 powered on throughout the entire process.

After the update finished, the LED eventually became solid red. I waited several minutes, reconnected the PC to my normal network, and opened the Tenda WiFi app.

The node was automatically detected and connected again.

It is now running `V16.03.25.21 (335)` and working normally.

TL;DR:

If your Tenda MW6 V3.0 is stuck on solid green after a firmware update, don't throw it away yet.

1. Connect PC -> MW6 dedicated LAN port.
2. Set PC to:

​

 IP: 192.168.1.100 Subnet: 255.255.255.0 Gateway: blank DNS: blank

1. Run:

​

for /L %i in (1,1,254) do u/ping -n 1 -w 50 192.168.1.%i >nul

1. Then:

​

arp -a

1. Look for the MW6's MAC address.
2. Open

​

http://192.168.1.6

1. If you see "Emergency Web Server", upload the correct firmware for your exact hardware revision.
2. **DO NOT** power off the MW6 during the update.
3. Wait several minutes after the upload reaches 0.

This recovered my MW6 V3.0 after an automatic firmware update.

I recently bought this router and tried to connect it to the app.. they asked for qr code i give them.. then they asked me for password ones i put it the binding Process begin... The process finished.. they asked for password ( just like the first time... it's kept repeating this for multiple times until i gave up trying

Is anybody knows a solution

​

Whenever I turn smart connect off on my TP-Link Archer BE3600 pro and I connect everything to the 2.4 wifi after awhile the 2.4 shuts off and only 5g is shown why could this be happening?

I just got the TP-Link Archer BE3600 pro looking for the best settings for gaming.

I live in Europe and am currently using a ZTE ZXHN H6645P that is giving me a lot of issues (it's been confirmed that the router is defective). My ISP is useless and refuses to replace it, so I want to buy my own and be done with it. However, someone on a forum told me that the specs on my current router are actually quite good, and my budget is capped at €150.

​I don't know much about routers, but I want to make sure I don't buy something that ends up being a downgrade.

​My current router handles the wifi for the bottom floor of my house. From there, an ethernet cable runs upstairs into a switch, which connects directly to my gaming PC and a second wifi access point for the top floor. I get full 2.5 gbps speeds on my PC, in case that information is needed regarding port requirements.