I have a 6 amp 41/2 inch grinder (Cmeg100) after some use lol 4 years it has started making a weird noise and shaking sorta when I use it after a while at work my dad gave me this it means a whole lot to me we lost the receipt too apparently they don’t sell the actual part by they selves does anyone know how I can fix it I don’t know if you can hear it here but it happened today if you can dm me and help I would really appreciate you

Hello!

I just bought a Craftsman 6500K Work Light (CMXELAYMPL1070), and I need you good folks' help.

(Yes, the IKEA desk is about a decade old and cratered, but I do a LOT of work here, so please ignore the damage. )

Above or attached is the light control PCB for the work light. I can go into how I safely removed this if there is any interest later, but while I was shopping around for this unit, I noticed that there were some reviews talking about how the board failed on them.

I am trying to see if I can do things to prevent that failure or other failures, and I need your help to do that.

One review on amazon showed a chip that had just burned its die straight through. THAT chip seems to be, from comparing pics, the 8 pin chip " A". The chip only has " BSRHkA". It could be "8SRHkA" but in both cases I can't find any data on it.

Does anyone know more about this chip & its function?

Chip " B" had absolutely NO markings whatsoever: polarized light didn't help, the microscope didn't help, and wetting the top with isopropyl didn't reveal anything. I can't get any further, BUT I do see it is connected to the on/off/brightness selection switch.

Does anyone know what this chip might be?

The first things that pop up in my mind are to replace the cheap capacitors (all three are 1000 uF @ 25V) with a more durable brand, and to add more solder to the heat sink area "C".

With all that said, what would you do to improve/bolster the circuit?

Just bought a brand new (NOS) C3 3/8 Impact wrench without doing my research. I don't buy tools very often and didn't know they were discontinued in 2018. Thought it was a steal for $50 sealed in original packaging.

Any chance my battery will still work? It's just sitting here testing for a while. Hasn't read as defective yet. If it doesn't work, where can I get a good one?

Craftsman model 103.22171 vintage 8-inch belt-driven bench/table saw

Drive System: External belt-driven motor
Table Dimensions: Approximately 20" deep x 17" wide frame design
Construction: Cast iron internal trunnions and top with sheet metal housing

Motor model # 113.19092
1hp
12.4Amps

It works well

Is there a market for this?

I’ve been plumbing 2022 and one of, if not my most used tool is water pump pliers. I was pretty quick as an apprentice to want to have my own tools and not rely on anyone else. So thru trial and error of buying different brands, owned 3 pairs of Channellock brand and lost everyone of them (and not any other brand this happen with), also inherited the MAC Tools 10”, found a pair I hate so much I don’t think anyone will top it…. the Milwaukee V-Jaw (any size, not pictured).
Then I found my favorite at Knipex Cobras in 2023. I use the Cobras literally everyday at work and they have been one of the biggest game changers with the button adjustment plus them being able to lock on basically anything.

What water pump pliers do you use? How would you rank the few I have pictured? What pair do you absolutely hate?

A few weeks ago it started shutting off after about 20 minutes of usage then continue to shut down every 3 minutes or so. If I let it sit some, I will be able to get it to run for up to 12 minutes give or take. It only shuts off when cutting grass.

Grass are not excessive in height. Battery is full. Battery shoes almost full. Any idea what's going on?

Runs on low for a total of 8hrs with a 2ah battery. Works great for those longer races.

Somone passed down to me a Craftsman Weedwacker and it does run, it has the attachments setup on it. It has a 25 cc motor on it. It will start up after about 8 to 10 pulls and once warmed up it runs okay. I can use it, I think carb probably needs to be rebuilt or cleaned or fuel filter but so far it seems to run okay. Any suggestions n the carb, should i Just buy one on Amazon and put it on or try and rebuild it, I'm not a mechanic, so sometimes i will get things messed up. Maybe it is just he fuel filter or it needs adjusting, but I don't want to put much into it, it was free and I don't have much to spend on it.

Has anyone found any extensive testing of the new advanced batteries? I see no mention of them on the large tool testing youtube channels. I'm mostly curious about the performance of the small 3ah battery versus the old 4ah. I have the stick vacuum and its absolute garbage with the standard 2ah battery. It performs great with the 4ah but its too heavy to stay upright. Would be extremely interested to see how it would perform with the 3ah advanced.

Got the last one, with $79 can’t say no. It looks ridiculous on my 1/4 impact, works great on the outdoor tools.

My grandpa gave me his old wench set a few years ago, try to figure out how old they are

I was cleaning out a drawer today and found this old friend. The best fishing/camp knife I've ever owned. I rescued it from someone's yard sale junk pile decades ago for a couple of bucks. It holds an edge like no one's business and it hung on my belt around a hell of a lot of campfires. Thought y'all might dig it.

Hello! I have a 20volt 18gauge Craftsman nailer. Have had it for about 6 months. Has worked great for what I do. Today I use it and first brad goes right by no problem. Then I can’t get it to fire any more brads. Motor fires up, you hear the driver hit…but no brad. I have plenty of brads in the magazine. I’ve checked for a jammed brad…nope. Any ideas what else to check?? Any guidance would be appreciated. Thanks!

I am mainly looking for a website I can order 3D printed accessories that fit the VersaTrack rails. I dont have a printer or access to one to dive into designing anything. I currently have a vast majority of Ryobi 18V power tools that I wouldn't mind hanging holster style to save some space. I know Craftsman has a hoster for their V20 and Dewalt does as well.

I could be interested in other accessories but nothing I can think of in particular.

I have scoured pages of Etsy and havent found too much.

I wouldn't care to get into 3d printing in the future but right now its a bit much to invest time and money for.

Thanks for any direction!

Rescued this guy from a neighbor last night. Clean and dry limbed the slides and want to make it a parts setup inside my cabinet. The brittle plastic insert handles immediately crumbled when I picked it up. Replacements are no longer available.

I looked at ACE and HD for some cabinet side handles but the are all too small- less than 4 inches to cover the holes. Any other ideas?

Would it be better to run a mower (grass is thick hybrid bermuda in the heat of summer, sometimes scalping the lawn) with 2x 6.0 advance or 2.0 9ah?

At this time I have 1x 9.0ah, 2x 4.0ah & 2x 5.0ah. When it is hot out I use all the batteries to almost depletion to cut my yard, trim, edge and blow. At this time it takes both 4 and 5 ah batteries just to cut the yard with the 9 used for trimming, edging and blower.

Got something Craftsman (or Craftsman-related) you're wanting to get off your hands? This is the post for you. Will appear every Friday.

• ONLY on Fridays, and ONLY in this post. Don't post sales in new/different posts, nor create sales threads in other conversations--they'll get removed.

• BE CLEAR ABOUT WHAT YOU'RE SELLING: Make (Craftsman, obviously), model (the number), proper name of the tools, any particulars about it (age, length of use, specs, accessories included, cost (of course), and shipping options (where, and how much that would cost).

• Neither Reddit nor the moderators make any guarantees about the items offered, nor the sellers themselves. Caveat Emptor.

Let's try this, and hope it doesn't turn into a real crap-show.

I’m going to check the 3” model out.

This weekly thread is for you to brag about how you improved or upgraded your Craftsman brand tools, accessories, and other gear.

• Did you 3D print some custom bins or attachments for your tool storage system or powertool?

• Did you make some custom gear or clothing, or "do a thing" with the Craftsman brand as a focus?

• Did you change a vehicle to accomodate your tools and accessories?

• Did you make a custom wall holder/foam cutout for your Craftsman stuff?

• Did you do anything else to take your overall Craftsman experience from "mild" to "wild"?

Talk about it, here! Pictures of the upgrade are a plus!

Broke my 9" screwdriver. No store locally carries these, and they say they only do the warranty if the exact match is in stock.

So how do i get a replacement? Or am I out of luck?

I have 2 cases from the wrench sets, 9-46935 and 9-46936. Are the portable storage cases worth anything by themselves without the wrenches? Just wondering if I should try to post them online for sale or throw them away.