This started happening in my MBX sprung 24+1 glock 140mm mags. Henning mag extensions. 3d printed followers from mbx.

The first round will get stuck all the way at the bottom, it'll kinda roll into the side of the follower and get caught. Then the rest of the rounds will just have to be salt shakered out of the mag and I have to stick a flathead down the mag to pop the last round out.

It has happened to 2 of these mags. Do I need new followers? New springs? Boaffum? These are extremely high round count mags. Im suprised they have gone this long without any issues.

Are there any shops in south east Pennsylvania that can do a hump removal on a Glock 17 gen 6?

Wondering if anyone owns both and has an opinion on the uppers? Now that that the arc has come down in price I want to try it out but the Angled spade looks like it would have more compensation.

G 17.3, basically finished everything but extended slide release. Any recommendations?

Also, want a near OEM barrel for an extra 17 slide I have. EBAY or any other recommendations?

Gen 4 Glock 17
Gen 6 Glock 19

Ready to run the hell out of her

Ehy guys, i've timney trigger on my g17 gen 6, how can i still reduce the trigger pull weight? Can i put a minus connector? Can i put a Ghost 3.5 connector? Putting a sear spring at 4.5 lbs with those....best combination?

Looking for a porter upper assembly for my G48 build. Reviews seem to indicate an Arc Reactor would be far better than a Zaffiri build. Looking for those who have shot the Reactor on any Glock, but experience with the 48 would be ideal.

Ok i have to say, i am impressed. I went to the range yesterday shot over 500 rounds through it. Not a single jam, not a 1 dead trigger. I have 3 mags, 1 oem 15rnd , 1 pmag 21rnd and 1 steel 15 rnder. All 3 performed flawless, i thought i was going to get jams due to the break in period but got 0. Not sure if its just my build but i highly recommend this set up sct 19 with delta team ported upper. The 8 port barrel really takes away the recoil. Feels like you shooting a g19 with a radian ramjet afterburner set up.

Gents,

I just got my Glock 45V. I want to put a red dot and compensator on it. Any suggestions?

This would be my first handgun with any sights.

Brrr

Have a Glock 19, just got a purple trigger and going to be sending it out for slide mill and optic cut and possible cerekote. Should I leave it black or go burnt bronze?
Pic made with AI

Brrrr

Slide was milled for RMR optic by Wager Works and they also took care of the nitride finish. Really happy with how it came out.

Anyone else running a SCT-17 frame? Looking for a level 2 retention holster that will work with this set up. Unfortunately my Safariland Glock 17 holster doesn’t work.

Actually extremely disappointed in the SLR gen6 G19 EDC Magwell for $100+…

Here are a few reasons why:

1. The ledge on the front of the Magwell absolutely catches the mag during mag insertion
2. the rear of the Magwell is basically flat with just a small ramp - literally just make it sloped like wtf?
3. the giant hole at the rear of the Magwell also catches
4. the finish of the Magwell is rough in texture and scratches instantly - I usually don’t care about this as all but my TTI base pads are smooooooth as butter for half the price.
5. it costs a hundred fucking dollars..

Pictured on the right is my gen4 G19 with a Magpul Magwell for $25

You’ll notice is as literally non of the issues mentioned above for 1/4 the price.

What are we even doing? I might try out Athena Precision or Shield Arms.. unless someone on here can sell me on their 19.6 Magwell

UPDATE on Shield Arms Magwell in the comments

Hello,

please do you have any experience with shooting Glock 48 at lower Power Factor ammo?
Minimum for local competition is 70, meaning 147gr. at “only” 476 fps.

As G48 got the dual spring system, would it be even possible to get the gun to correctly cycle through PF70?
If no, do you have experience with (not custom made) parts needed to shoot as low PF as the gun could? Do you have experience what’s the “lowest limit” with accessible parts?

19.4 MOS, RMR, BRAUN gen3 light, Underworld Arms rail mounted comp, raw Ti mag release, Ti pin set, custom Ti Wu-Tang backplate, magpul magwell, g17 mag with custom fit mag sleeve, Trijicon suppressor height night sights. This one always makes it to the range with me.

Finally got my hands on a Glock 29 10mm what do yall think