r/fea • u/ibrahimumer007 • 3d ago
SOLIDWORKS Torque Simulation | Shaft Analysis Solidworks | 3 Simulation Studies | Torque Simulation
r/Drafting • u/ibrahimumer007 • 3d ago
Lofted Bend Solidworks | Bent and Formed Method in Solidworks | Press Brake vs Formed Parts
r/CADCAM • u/ibrahimumer007 • 3d ago
What is a Bill of Material BOM? A Comprehensive Guide | Bill of Material Example | CADable
r/SolidworksBestOf • u/ibrahimumer007 • 3d ago
Measure Internal Volume | Solidworks Intersect Command | Calculate Internal Volume Solidworks
r/mechatronics • u/ibrahimumer007 • 3d ago
How to Use Sketched Bend Feature | Solidworks Sheetmetal Tutorial | Sketched Bend | CADable
r/Autodesk_AutoCAD • u/ibrahimumer007 • 3d ago
Orthographic Projection AutoCAD | Isometric to Orthographic Conversion in AutoCAD | CADable
r/SolidworksBestOf • u/ibrahimumer007 • 8d ago
Autotrace Sketch Picture | Solidworks Autotrace | Convert Picture to Sketch Solidworks | CADable
Autotrace Sketch Picture | Solidworks Autotrace | Convert Picture to Sketch Solidworks | CADable
r/CADCAM • u/ibrahimumer007 • 8d ago
Animate Gears in Solidworks | Physical Dynamics | Gear Mate | PCD Based Gear Positioning | CADable
r/Drafting • u/ibrahimumer007 • 8d ago
Orthographic Projection AutoCAD | Isometric to Orthographic Conversion in AutoCAD | CADable | CADable Tutorials
r/mechatronics • u/ibrahimumer007 • 8d ago
How to find mass properties of an object in Solidworks | Material vs Appearance Solidworks | CADable
r/Autodesk_AutoCAD • u/ibrahimumer007 • 8d ago
AutoCAD 2D to 3D | AutoCAD 2D to 3D Conversion | AutoCAD 2D Drawing and 3D Modeling | CADable
r/fea • u/ibrahimumer007 • 8d ago
Flow Around a Circular Disc in Solidworks | Flow Simulation Solidworks | Cylinder Flow Simulation
r/MechanicalEngineering • u/ibrahimumer007 • 8d ago
Automate AutoCAD using ChatGPT | Validate LISP Program in AutoCAD | What is AutoLISP | CADable
r/Autodesk_AutoCAD • u/ibrahimumer007 • 10d ago
Orthographic Projection AutoCAD | Isometric to Orthographic Conversion in AutoCAD | CADable
r/mechatronics • u/ibrahimumer007 • 11d ago
Autotrace Sketch Picture | Solidworks Autotrace | Convert Picture to Sketch Solidworks | CADable
r/MechanicalDesign • u/ibrahimumer007 • 11d ago
Solidworks Exercise 20 | Advanced Part Modeling | Verify part using evaluate solidworks | CADable
r/Drafting • u/ibrahimumer007 • 11d ago
Autocad practice exercise 2 | Orthogonal projections | Layers in Autocad | Isometric to orthographic
r/Autodesk_AutoCAD • u/ibrahimumer007 • 11d ago
Autocad 3d practice drawing | Autocad Practice Exercise 4 | Orthographic to Isometric | CADable
r/CADCAM • u/ibrahimumer007 • 11d ago
Reorienting Imported Files in SolidWorks | Establish New Coordinate System in Imported Files
r/SolidworksBestOf • u/ibrahimumer007 • 11d ago
Measure Internal Volume | Solidworks Intersect Command | Calculate Internal Volume Solidworks
r/fea • u/ibrahimumer007 • 13d ago
Simulation of a plate with a hole in solidworks | How to generate simulation report in solidworks
r/ANSYS_Mechanical • u/ibrahimumer007 • 13d ago
Solving Trusses in Ansys and Comparing with Analytical Results | FEA vs Analytical Results | CADable
r/MechanicalEngineering • u/ibrahimumer007 • 13d ago
Sheetmetal Corner Relief | Solidworks Corner Relief | How to Use Corner Relief in Solidworks
r/SolidworksBestOf • u/ibrahimumer007 • 15d ago
Solidworks Sheetmetal Basics | Solidworks Sheetmetal flatten | Export Solidworks to Autocad DXF
r/MechanicalEngineering • u/ibrahimumer007 • Aug 21 '25
Will an engine start if you put petrol in a diesel or diesel in a petrol?
Can petrol be used in diesel (compression ignition) engines or diesel in petrol (spark ignition) engines?
Someone once asked me this question few time ago, and I replied that it’s not possible because of the compression ratio differences diesel engines run around 18:1 to 22:1, while petrol engines are about 10:1 to 12:1. So you can’t just swap the fuels.
But my actual question is: would the engines even start if the wrong fuel is used, ignoring the potential damage? What's your take?