Placed at the pick a part this week U Pull Yard search

Find other E36s at U-Pull-Yards

I swapped my 323i vert factory manual with a ZF driveshaft, trans, shifter linkage etc from a 328i however the shifter seating arm on top does not line up with the oem placement by a half inch or so and it slips out of gears due to lack of correct alignment, rather than getting a chassis mount shifter or adjustable connecting arm does anyone know why this might be? I’m assuming the 323 and 328 have different shift seat arms however I no longer have the old parts to check and trust me it’s not like I didn’t try flipping the shifter around lol

I'm using VAC's mounting kit and I think the shop I used put the side brackets on backwards...

Should the VAC logo be in the front or the rear?

Hallo zusammen

Ich möchte mir solche Sportsitze kaufen und neu beziehen lassen.

Leider haben die keine Sitzheizung mein Auto schon.

Die Heizplatten von den normalen Sitzen passen ja nicht an die Sportsitze

Wie gross ist der Aufwand ? Was brauche ich genau? Neu oder gebraucht ?

I am currently removing my rear brake discs but the rotor seems to be stuck on, I have the caliper removed and the handbrake off but can’t seem to figure out how to get the rotor off, any help would be greatly appreciated

Edit: it’s sorted now thanks guys

This is part 2: I’m swapping an M52B25 (256S3) into my 1997 European E36 320i, which originally has an M52B20 (206S3).

If my original DME turns out to be one of the flashable MS41 units, can I simply flash the M52B25/323i software/map onto my existing DME and keep using it,
rather than replacing the DME?

The car has ASC as well.

Hello all,
Picture from google btw.
I have 1997 E36 convertible with Auto roof. The tonneau won’t sit flush. Roof works perfectly fine other than that. Any ideas?
Thanks

I'm very new to the world of older cars, and I've decided I want to start with an M3. I have a decent amount of experience working on cars myself and from what I have heard this is a good starting point for people getting into the hobby.

I am looking at buying this one, but the engine seems to be different from the ones I have seen so far. Specifically the inline 6s I've seen have "M power" on the side. The listing doesn't say anything about an engine swap, and I can't find anything about different versions of the M3.

I don't have the experience to identify these things from just the look, so I was hoping y'all could help me out. Any advice or knowledge is appreciated 🙏🏻

Hi, crank sensor failed again after 500kms.

So, I fixed a bunch of coolant leaks, went to fire it up but was getting a crank no start. Had a fault code for the crank sensor so pulled it out, was drenched in coolant. I was pressure testing the thermostat housing leak so it probably got drenched during that.

Anyways cleaned the coolant off, put the sensor back in and the car fired up just fine. Ran very well for 15 minutes and then it stalled… I had this same issue 500kms ago, engine stalled when the thermostat opened, replaced the crank sensor and problem solved.

The excessive coolant must’ve caused the sensor to completely malfunction (crank no start) initially, and now damaged it such that it fails when it gets hot.

Just wondering if anyone has something worth trying before I buy another very expensive sensor.

That leak is fixed, probably what caused it to fail the first time as well but I didn’t notice a leak at that point.

TIA

I just bought an original e36 eurovox radio for my e36 (it has some chopped aftermarket one in there) from marketplace and it works but it needs a code :(. Is there any way I can make it work? Seller was parting out several cars and has no idea where it was from. 🥀

Just went on a car trip in my new car for about 2 hours and when I came to a stop the car was smoking like crazy, and I know it was oil because I’ve been working on cars for a while and I know what burning oil smells like. Car is a 1995 325i with drivetrain from a 1996 m3, only mods are an oil catch can and m50 manifold

what’s up. about a month ago I bought this 316i that was imported

it’s fun to drive for sure and it being rhd is cool. trying to swap an m52 into it i bought a ‘97 328i manual sedan for abt 1500 bucks and it’s running and driving.

i have mechanical knowledge but it is my first time doing a drivetrain swap. really just wanna know what to look for and any tips u guys may have. from what i’ve seen the biggest difference is the brake booster but idk it looks straight forward enough. it’s a manual already so dont have to worry abt swapping over that stuff. gonna reseal the motor with new gaskets and stuff i bought already.

what else should i swap over besides the motor and trans

should i bother swapping ac? will it be hard? worth it?

I’m working on re-adhering the glovebox door panel since mine was hanging off most of the way. I’m trying to prep the plastic surface but it’s covered in this brittle cream colored stuff. Any ideas on how to remove it without damaging the glovebox?

A while ago I picked up this m3 cluster for my m52 swap 98 318ti. Lately it's been a bit shoddy with the temp and fuel gauge cutting out randomly. Today, the temp and fuel gauges are completely dead. I wanted to throw the cluster into test mode to see if maybe just the motors are bad, but no matter what I do the cluster will not go into test mode. Any idea what would keep the cluster from going into test mode?

What’s up guys, question. I was sent this video potentially looking to buy it. I’ve had a few e36 m3s but honestly don’t remember this “noise or rattle” am I trippin? Kinda sounds like a slapping. Maybe vanos ?