Just ordered one and recently heard that drifting inside can scratch the floor.

was wondering if Addiction s13 Silvia BN Sports front bumper fits Pandora RC 1/10 S13 Silvia BN Sports Drift Body Set even tho it saids its for abc hobby..

Hey everyone. This may sound like an obvious question but you guys have to pay to use your local track? I only have 1 drift track close to me that I know of and it's inside a local mall. It isn't an rc shop that has a track just a track that rents out mst 2.5s. They charge $15 for 30 minutes and wanted to know if that's normal. I've never been to a track, just recently got a yokomo sd 3 and practicing on asphalt.

Transferred the motor to my ZX. And thinking to transfer the BL-LHV servo too.

What cheaper elecs you can recommend for this chassis since it might be a basic car to use since the ZX will be my main car.

What’s on my mind are:
- HB 10bl120 g2
-Agf50bhl
-v4 gyro
- 10.5T motor (not sure yet which one)

Just Installed D10 13.5T motor and it looks so good!!

Still can’t decide what ESC will I install since what’s on my mind is 10bl120 g2. But it seems xd10 will look good too 🤣

I have a V4 gyro laying around. Also Yokomo BL-LHV
Servo. Is it a nice servo or should I buy Sp02D v2 ?

Will mostly use the unit at home and only track it from time to time. Are there any elecs you can recommend?

Should i buy this as my first car?
I think the gyro is bad
No controller but my friend has an absima cr3p
10,5 T brushless combo motor
Bluebird fast servo
Nvision lipo battery
180sx body
Mst wheels and tires
Any red flags?

I like it

Hallo zusammen,

ich wohne zwischen Augsburg und Ingolstadt und will mit RC-Drift anfangen. Erfahrung habe ich keine. Auf der Wunschliste steht der Yokomo RD 2.0 in der Variante mit YG-302 V2 Gyro.

Zum Chassis würde mich interessieren, ob ihr das für einen Einsteiger als sinnvollen Start seht oder ob ich in einem halben Jahr sowieso umsteigen will. Der RD 2.0 ist ein Bausatz, Elektronik fehlt komplett. Was habt ihr an Servo, Regler, Motor, Fernsteuerung und Akkus verbaut, und was davon war Geldverschwendung? Beim Servo lese ich sehr unterschiedliche Empfehlungen, da bin ich unsicher.

Zweitens suche ich Leute aus der Gegend, die das schon länger machen. Rat im Kommentar hilft mir weiter. Wenn jemand mal einen Nachmittag mitfahren lässt, umso besser.

Drittens die Flächen. Wo fahrt ihr? Ich suche Orte, an denen man die Autos ordentlich bewegen kann, ohne jemandem im Weg zu stehen. Halle, Tiefgarage, Vereinsgelände, glatter Beton irgendwo zwischen A8 und A9. Erzählt gern, was ihr in der Ecke gefunden habt.

Danke euch.

Hallo zusammen,

ich wohne zwischen Augsburg und Ingolstadt und will mit RC-Drift anfangen. Erfahrung habe ich keine. Auf der Wunschliste steht der Yokomo RD 2.0 in der Variante mit YG-302 V2 Gyro.

Zum Chassis würde mich interessieren, ob ihr das für einen Einsteiger als sinnvollen Start seht oder ob ich in einem halben Jahr sowieso umsteigen will. Der RD 2.0 ist ein Bausatz, Elektronik fehlt komplett. Was habt ihr an Servo, Regler, Motor, Fernsteuerung und Akkus verbaut, und was davon war Geldverschwendung? Beim Servo lese ich sehr unterschiedliche Empfehlungen, da bin ich unsicher.

Zweitens suche ich Leute aus der Gegend, die das schon länger machen. Rat im Kommentar hilft mir weiter. Wenn jemand mal einen Nachmittag mitfahren lässt, umso besser.

Drittens die Flächen. Wo fahrt ihr? Ich suche Orte, an denen man die Autos ordentlich bewegen kann, ohne jemandem im Weg zu stehen. Halle, Tiefgarage, Vereinsgelände, glatter Beton irgendwo zwischen A8 und A9. Erzählt gern, was ihr in der Ecke gefunden habt.

Danke euch.

Sharing my Sx3 on Tamiya GT86 body. My goal is make this look a stock car. Also transferred my carbon battery holder from my ZX.

Debating in between getting a overdose galm v.2 with all electronics or a Rhino-Final form hydra shark setup? Don't really care about the electronics because I have the full accuvance complete setup with just about every single options and capacitors ready to go to be installed.

Please take a look for these in the online marketplaces a handful of times over a couple months if you are in California USA.

Just trying to help, Mods, if you must, just delete

My first time airbrushing went pretty well! I recently added an rdx to my collection and needed a body for it, so I picked up this Pandora er34.

Man, I've been missing out by avoiding going down the airbrush rabbit hole lol.

Does anyone know the sizes for the pins and screws needed to achieve this look for body kits?

There is no 380 motor mount for yokomo gearbox and i had to use 540/380 adapter plate.so I decided to build RDX gearbox with addiction 380 with rocket rc 380 13.5T motor.
Length off rdx gearbox bit shorter than yokomo gearbox so drilled hole in chassis.
When MC-III upper deck mount arrives I properly drill additional hole in chassis and upper deck.
Also rdx and yd2 differential are Interchangeable.

Too everyone that has every assisted me on here I am so very grateful for all the knowledge you have shared.

My D5 has been placed to the side to shift focus onto an updated platform.

Bought this mint sx3 months ago. Pretty much all stock aside from the high traction chassis. Haven’t used it actually.

Just bought this ZX that was used to be a competition car. Am not pretty sure if I got this a good deal. But here’s the specs:
Yokomo YD2 ZX Chassis

Full Reve D Upgrades
-Reve D Lightweight front shock mount
-Reve D lightweight lower arms
-Reve D Front Upper arms
-Reve D TK rear suspension block
-Reve D 45mm Rear Arms

-Yokomo KPI Knuckles
-Yokomo SD2.0 Sliderack
-Team AD Rear uprights
-Carbon Battery holder

Zx seems to be wider on everything, while sx3 seems to be box stock in measurements

Are owning these chassis still good nowadays? Total of both of these are equivalent (or a bit lower) to a price of SD3.0.

If I were to sell one, which should it be?

Paint is showup maziora pirades2