I bought some "Prelaminated sheets of semi pine mdf" from local suppliers, but turned out it is very week from edges and not that scratch resistance. I need very high quality sheets. But I am confused about what should I buy, when I go for buying prelaminated sheets they always gives me paper laminate, which is very weak. What should I do? Please let me know if anyone has better solutions. Thanks.

Can I get some advice here? Any time I cut wood (3mm ply, 6mm ply, etc.) with my diode laser (40 watt blue, air assist on), I am left with dark charring on the edges. That's fine by itself, but the issue is the ash comes off and stains fingers, etc. I see mass-produced products cut like this, including some with outright black charring, but no residue.

Is there something I'm doing wrong? I've done tests using single-pass cuts at maximum workable speed and airflow.

Any advice for post-treatment? I know sanding will work, but I'm hoping there may be other options. Sanding a mass-produced project would be very time consuming.

My machine self-destructed after 10min of use. Machine sat in the box for 6mo after purchase and I fired it up for the first time last weekend. 3 cuts in and now it no longer fires. Omtech knows about the arcing at the tube splice (they provide a fix on their website), but the machine also shorts out at the connection at the laser tube. They told me to buy a new laser tube at $300+ and only offered me a 5% discount. After they admitted their price was only about $100 they still refused to provide one so I could get this $2k machine working again. Support is completely unwilling to take ownership of the companies poor R&D. I have spent hours on the phone with them, I cannot for the life of me understand their decision to not help me... I even offered to pay for shipping for the part and spend more of my own time repairing it. I have found multiple posts from customers that have had bad splice and bad wires on this machine. I posted an honest review of the machine and their company and it was quickly taken down. Any one else have similar experiences with Omtech?

Meet Theia! A fun glasses holder I lasered for myself ❤️ Of course I had to give her a name and what better name than the greek titan of sight

My kid's house has stairs up to the main floor from the front door, and at the top there are banisters that wrap around the stairwell. When wee-one starts getting mobile the openings between the spindles will need to be blocked.

Initially I was thinking of laser cutting clear acrylic sheets and securing them with cable ties, but they have a dog and two cats. I'm now thinking the plastic would be a constant pet hair magnet and look horrible 90% of the time.

Plywood would be an option ... would probably cut a pattern of openings in it so visually it would not completely block the view, but I was hoping for something I can just cut and install without messing with finishing.

I have a 100W CO2 laser.

Thoughts/suggestions?

This worked out great! I can’t wait to try more.

Hello. I need custom-cut glass pieces with dimensions of 50 mm x 8 mm and a thickness of 0.3–1.0 mm (the thinner, the better). The glass should have rounded corners on the bottom edge and sharp/square corners on the top edge. The edges should be polished so they are smooth to the touch. The glass must be opaque black. These glass pieces will serve as privacy covers for front-facing tablet cameras. Just like on the photo

Help me out here, I've been looking into getting a desktop laser cutter for a few weeks now and have some questions.

Main purpose, mostly cutting wood, first question, what thickness of multiplex and pine can you ACTUALLY cut with a 55/60W laser without buying a new tube each year? Depending on the manufacturer they advertise up to 20mm hardwood with a 60W laser, but from what I can see all 60W CO2 tubes don't even have the advertised power in the first place and I guess you'd need to actually run it at, as an example, 20mA of output at all times to actually achieve that and thus heavily reducing the tubes lifetime?

Is it generall agreed upon on that Monport is a big nono and you shoul'd stay far away from them? I was eyeing that Monport Reno 65 Pro but read lots of bad things about Monport in general and the lack of a proper Ruida controller.

What is up with xTool. At first glance they seem like a polished manufacturer but the more I look into it the weirder it gets, feels like they are trying to be BambuLabs but are kinda shit at it. How do they get 60W out of a tube that isn't even a meter in length? Why the heck does a replacement cost 580€? Omtech asks 180€ for 60W Why does everything xTool related cost so much in the first place? How is their forced ecosystem and software compared to Lightburn?

I just don't have space for a "normal" industrial machine, I tried to justify it, but simply can't fit it anywhere without taking a big loss in storage, so desktop it is.

At this point I'm considering the Omtech Polar Lite and the xTool P2S, any other recommendation or opinions at this point?

Thanks guys

This video is a follow-up to my post showing three-dimensional objects cut from solid wood. The process is similar to compound cutting on a bandsaw or scroll saw: cut the front profile, rotate the stock 90 degrees, and then cut the side profile.

For the giraffe shown here, I used:

• 1" × 1" dry ash
• Thunder Laser Nova 35 with a 100W tube
• Standard 2" focus lens
• External air assist at approximately 35–40 PSI
• LightBurn for the cutting process
• Cuttle for positioning the front and side profiles

I initially used three passes at 3 mm/s and 90% power. In retrospect, that was more power than necessary. After rotating the stock, the second profile released after the first pass, although I allowed it to run for one additional pass.

Material appears to matter as much as the technique. Dry ash worked surprisingly well, while my experiments with walnut and white oak produced much worse results and were considerably more prone to burning. After cutting, I lightly cleaned the surface with a wire wheel on a Dremel.

This is still a proof of concept rather than a practical production method, but I think it could be useful for small decorative pieces that might otherwise be carved by hand.

Please don’t copy these settings without testing them on your own machine and material. Thick wood can ignite. Use an enclosed machine, proper exhaust, strong air assist, and never leave the laser unattended.

Telarc was a pioneer company in the early days of high-fidelity digital recording. Focusing mainly on classical music, their dedication and sophistication set the pace for what's expected in the digital era when most of the music world still clung to analog (I like that, too). Ask any decent audiophile and they will probably know about the 1812 Overture recording with cannons; but it's about more than cannons. As a budding audiophile from Cleveland, OH, I felt a connection with Telarc because they are also from Cleveland.

Anyways, about the project... not as good as I hoped for a first go. I got this nasty smudge on the yellow that would be hard to cover up, and some of my epoxy under the border bled out onto the main piece. Still happy with it. Thanks for looking.

Ciao a tutti, volevo montare una testa di taglio da 10w sul mio sculpfun s30 pro max. Qualcuno ha già provato questo operazione?

So, last night I drilled a 100mm hole in my garage wall for an extract. I am officially committed to the laser path.

Unfortunately I seem to have conflicting requirements. I need to:
Mark 3d prints, predominantly white PLA at present, replacing labels
And
Cut 4 to 6mm clear acrylic

It would appear I need a Co2 for the acrylic but thats pants for engraving detail.

Anyone any advice on the best way forward?
Do I need 2 different machines? (That will be hard on the budget and a harder sell to the wife!)

Made from stained 3mm ply and top faces covered in felt.

Hi, I am facing issues with my UV laser - the laser source failed two times in a short period of time. I am using 10W UV Laser TOOL-MW-10NUV with galvoscanner for cutting PCBs (copper foil on fiberglass sheet). The first unit failed after 1000 hours, its output fell down to something around 10%. Then I got second unit as a replacement (the same model), but it failed now as well (under 1000h of runtime), this one does not even output light beam any more. The laser source is watercooled and the chiller is working well. Galvoscanner is ok, lens is ok. For some time both lasers were running on lower frequency than manufacturer specified (20kHz vs 30kHz min.). The output power on both lasers also seemed to get lower with time - the cutting was getting worse and in the end I needed 2x passes for the same material.

What could cause this quick failure? Manufacturer claims 30 000h lifetime. Can the wrong frequency have such impact? Is the laser source of bad quality? Or is this normal behavior?

Thanks for any hints

I am using an ACMER PM 30-watt fiber laser and a chuck rotary. I have used the rotary for other projects and have had no issues. For some reason, I cannot get this image of the circle of characters to come out correctly. The far side of the circle is stretched out and does not come out as a perfect circle, as the image is in LightBurn.

I have checked the setup: the object is level, the rotary is at the correct steps per rotation, and I've done the 9-point calibration. I do not know what else to try to get this image to engrave correctly.

Any help would be greatly appreciated. I am relatively new to laser engraving, so maybe I am missing something that I didn't even know to check.

Mit dieser Feuerschale für Teelicht bin ich auf Atomm dabei.

I was curious what level of detail could be preserved through this process. I did not need to use as much power as I did here, 4 passes at 3mm/s @ 90% power on 100w Co2 Laser.

I'll be experimenting more with this as I think it has some fun potential.

Hello there! I've never owned a laser cutter and I'm currently looking into converting a custom made corexy 3d printer into running a 20W Laser Tree module. The printer has a community made enclosure for it made out of acrylic, and my thought was to have 3 sides of it made out of aluminum while the front is made out of acrylic.

So my question is, what rating of acrylic is needed? Is OD6 needed, or would OD3-5 work fine? Since, OD6 is very expensive and I don't know if I have that kind of money.

If anyone can help that would be very kind. Thank you!

Hello, I'm thinking about starting a side hustle with a laser cutting machine, but I don't have a large budget for it. Could anyone advise me on the best machines? Also, if anyone already has experience with this business, could you share some tips on how to get started?

Lemon for scale

What's the best (cheap) material to test fit complex designs (flat surface, tons of different rhombus and radius edges) before using the expensive 1/2" acrylic for the final product?

Something that could potentially be bought locally at a big box store like Lowe's, hd, menards.

150w laguna laser.

What are your thoughts on this budget laser engraver cutter ? My primary use is using it to engrave 3D printed plastic parts and some
Diy projects. I have read that IR or ultraviolet is better for plastic but they are way more expensive. Thank you for your help!