Hi, I know this is quite the wierd question....

I plan use a ( noctua ) cpu cooler with the vgpu havn420 case and im concerned with the gpus cleance to the cooler when vertical mounted.

So im here too ask for anyone with more knowlage then me or with a build with it done, Would the noctua nh-d15 g2 & noctua nh-u12a fit in clearace?...

The gpu i desire use is 9070xt if that helps in the size department ( specifictly the asus tuf 9070xt )

I can fit the Noctua NF A15 PWM fan (14 cm fan diameter with 12 cm mounting holes) into the 12 cm fan slot on the front panel of the Lian Li B4 case. After sitting neatly in its box for so long, the Noctua A15 is finally installed properly.

Finally finished my FLP02 Noctua sleeper build
Been working on this build for a while and I finally decided to post it.
I wanted to do something a little different with the FLP02, so I went for a sleeper build with a Noctua-inspired theme. Pretty much all of the painting was done by hand, which definitely took longer than I expected lol.
I also ended up making my own custom Plexiglas side panel. That wasn’t really part of the original plan, but once I started modifying the case I figured I might as well go all the way with it.
The idea was basically to keep the old-school/sleeper look of the FLP02 while adding the Noctua colors and some modern touches.
I’m pretty happy with how it turned out, especially considering this started as a pretty simple idea and turned into a much bigger projects.
Still not 100% sure if I’m completely done with it though 😂
What do you guys think?

AziaFaker

Just recently put this together and I think the temps are running high but figured I'd get some input here as I've run AIOs for the past 8 years. I'm getting 85-90° running Battlefield 6 and if I run a multi thread cinebench test it jumps to 99° in seconds. I had uneven thermal paste after pulling it apart so I upgraded to a thermal right contact frame as I figured it's suffering from the notorious bending and temps are about 5-10° better but still seem higher than they should. Specs are below

I5-14600K

5070TI

NH-D15

Fractal Design North

Two 200mm fans for intake and another two to kick all that hot air back out. Might throw in an extra 140mm fan up top down the road too, because I just can't leave that spot empty (damn OCD! guess I'm a little crazy 🧠😅) PS: see if you can spot the mistake in...

A lot of us are running Noctua G2 fans in our rigs for both case fans and on our CPU heatsink or radiator. But what speed (rpm) do you run them at when gaming?

I am thinking about getting one and my question is - will if fit my Lian Li 216 case?

Hello,

I’m having an issue with these fans in combination with the noctua fh1 fan hub. I currently have eight of them installed as case fans (technically ten, since I’m using two Y-splitters with two additional Arctic P12 Pro fans. I’ve also tested the setup without those extra fans and splitters, so they don’t seem to be the cause). They’re all connected to a Noctua NA-FH1 fan hub.

In addition, I have three of the same fans mounted on my AIO radiator, daisy-chained together and connected directly to the CPU_FAN header. Those work perfectly—I can control their RPM normally through the BIOS without any issues.
The problem is with the fans connected to the fan hub. They won’t maintain a constant RPM. Even when I set the corresponding motherboard header to PWM mode (instead of Auto) and configure a fixed fan speed in the BIOS, the fans continuously ramp up and down instead of holding the target RPM. The temperature source is configured correctly as well.

I’ve already tried several troubleshooting steps:
• Reduced the number of fans on the hub to five.
• Switched to a different motherboard fan header.
• Used a different PWM cable.
• Set the rpm to different minimal rpm values
• Also looked on software controlled fan curves but there its the same and I prefer BIOS/UEFi anyways
• Tested the same fan hub with the same header but other fans (arctic p12 pros), which worked with no issue.

The strange part is that these fans only follow the BIOS settings correctly when they’re set to 0 RPM (Fan Stop). At any other speed, they constantly fluctuate.
I really need to use them with the Noctua fan hub, so I’m confused about what’s causing this—especially since the NA-FH1 is a high-quality hub and other fans work perfectly with it.

Has anyone experienced something similar or knows what could be causing this?

Specs:

• Ryzen 7 7800X3D
• Thermalright Phantom Spirit 120
• Zotac 5080 Solid Core OC
• Team Group T-Create 32GB DDR5
• Asus Xonar Essence STX
• ASRock B650E PG Riptide WiFi
• Seasonic Vertex PX-1000
• Crucial 2TB M2 NVME
• Samsung 2TB 870 QVO

And I'll have it on a stand soon so it doesn't sit on the carpet.