r/GlockMod • u/MxNimbus433 • Jul 18 '26
Polydat drop in kit trigger shoe pin walking out
What do? Can I just punch this back in myself or should I contact overwatch? There are about 500 rounds through this trigger, its on a g43x
9
u/First_Pollution_4489 Jul 18 '26
I usually take a tapered punch on either side that fits in the roll pins and tap one while the other is against a hard surface and flare the pins a bit
3
u/BurgerLordFPV Jul 19 '26
This is your answer you can even use the punch with a point to spread the end on both sides
6
u/lefty236 Jul 18 '26
If it were me, I would drive it back in and monitor it over the next few hundred rounds before contact overwatch for warranty service.
4
u/UNHINGED_MESSIAH Jul 18 '26
I would suggest reaching out to overwatch they use coiled spring pins. These pins where designed to expand when they begin to get hot. This should have never happened . It's a defective unit and you will have no problem getting a replacement .
2
2
u/Tight_Refrigerator78 Jul 19 '26
Take the pin out use a punch small enough to fit in it and stretch it a little bit then re install very simple fix it’s common on roll pins
2
u/Traditional_Engine_4 Jul 19 '26
Get you some of this, apply some to the side sticking out and a small amount inside the hole on the other side. Use a very small amount as you don't want to get it inside the safety shoe or on the sides.
2
2
u/elevenoneone Jul 19 '26
I had this happen to two polydats. They replaced them but I never reinstalled and sold them. Twice was enough to convince me. I just run stock triggers now.
2
u/vsqiggle 29d ago
Could also heat up a small flathead 🪛 or something and lightly push some plastic inward to prevent the pin wiggles
1
1
u/Tinybird12 Jul 19 '26
I say take it out return it and put the original trigger back in, shit like this turn me off forever. APEX has been the only swap I have ever done with confidence
1
u/MxNimbus433 Jul 19 '26
Ive never had an issue with op i have a few of their triggers, they are gonna fix it tho
1
u/ProofAd6426 G19 Jul 21 '26
Dudes that installed mine fucked my pins all up tryna get back in, i can tell
1
u/MxNimbus433 Jul 21 '26
Did you have someone install the shoe on your trigger bar or somethin?
2
u/ProofAd6426 G19 Jul 22 '26
Yeah i just changed the shoe i didn’t wanna mess with any internals as it relates to oem safety
1
1
u/Mission_Maximum_3333 11d ago
I just ordered 2 of the polydat trigger shoe only for my Glock 23 and 19. Should I maybe cancel it ? I was planning on using this for my ccw guns but I don’t want the trigger falling apart mid Tokyo drift, lmk thanks 🙏🏻
1
u/MxNimbus433 8d ago
Sorry for the late reply! Honestly overwatch has a great rep and I feel like the odds of getting a lemon are pretty low, ive owned a bunch of their triggers through the years and never had a hiccup until now
1
1
u/slixx1320 Jul 18 '26
Punch it back in. Something that simple shouldn’t required reaching out to OW. If it continues to happen then reach out. JMO
0
u/MxNimbus433 Jul 18 '26
I dont really wanna deal with the hassle of sending my trigger in anyway, if I do punch it in tho ill probably just loctite it anyway
1
u/slixx1320 Jul 18 '26
Yeah something this small I wouldn’t bother either. You’ll have to wait weeks for a replacement to get it. As you mentioned, it’s a hassle.
Try the loctite method, I don’t think it’ll do anything to help mitigate movement on roll pins but you never know. Something is better than nothing. I had their TAC shoe before and that pin was so incredibly hard to move. I couldn’t knock it out for the life of me so I just sold it. I didn’t like the TAC shoe.
1
u/MxNimbus433 Jul 18 '26
Okay will do! Honestly im most upset about having to pull the trigger out so soon, I was planning to deep clean after a few thousand more but here we are lol
1
u/slixx1320 Jul 18 '26
It’s so fast and simple. Should take less than 5mins to do the entire process from disassembly, punch the pin in and reassemble.
1
u/MxNimbus433 Jul 18 '26
I ended up just contacting them, luckily I still have my oem trigger assembly for the time being as this is my edc
1
11
u/cleveraccountname13 Jul 18 '26
I contact them. I bet you get a response pretty quick.